91̽��

Abstract:

Introduction: This presentation will describe the Modular Infrared Molecules and Ices Sensor currently in final assembly and test at the 91̽��, UK and VTT Finland for ESA’s upcoming Comet interceptor mission.The Comet Interceptor mission: The Comet Interceptor mission [1] was selected by ESA as the first of its new “F” class of missions in June 2019 and adopted in June 2022.  Comet Interceptor (CI) aims to be the first mission to visit a long period comet, preferably, a Dynamically New Comet (DNC), a subset of long-period comets that originate in the Oort cloud and may preserve some of the most primitive material from early in our Solar System’s history. CI is scheduled to launch to the Earth-Sun L2 point with ESA’s ARIEL [2] mission in ~2029 where it will wait for a suitable DNC target.The CI mission is comprised of three spacecraft.  Spacecraft A will pass by the target nucleus at ~1000 km to mitigate against hazards caused by dust due to the wide range of possible encounter velocities (e.g. 10 – 70 km/s).  As well as acting as a science platform, Spacecraft A will deploy and provide a communications hub for two smaller spacecrafts, B1 (supplied by the Japanese space agency JAXA) and B2 that will perform closer approaches to the nucleus.  Spacecrafts B1 and B2 will make higher risk/higher return measurements but with the increased probability that they will not survive the whole encounter.The MIRMIS Instrument: The Modular InfraRed Molecules and Ices sensor (MIRMIS, Figure 1) instrument is part of the CI Spacecraft A scientific payload.  The MIRMIS consortium includes hardware contributions from Finland (VTT Finland) and the UK (91̽��) with members of the instrument team from the Universities of Helsinki, Lyon, NASA’s Goddard Space Flight Center, and Southwest Research Institute.MIRMIS will map the spatial distribution of temperatures, ices, minerals and gases in the nucleus and coma of the comet using covering a spectral range of 0.9 to 25 microns.  An imaging Fabry-Perot interferometer will provide maps of composition at a scale of ~180 m at closest approach from 0.9 to 1.7 microns.  A Fabry-Perot point spectrometer will make observations of the coma and nucleus at wavelengths from 2.5 to 5 microns and finally a thermal imager will map the temperature and composition of the nucleus at a spatial resolution of 260 m using a series of multi-spectral filters from 6 to 25 microns.  Figure 1: (Top) The MIRMIS instrument for ESA’s Comet Interceptor mission. (Bottom) The MIRMIS Structural Thermal model under test at 91̽��.The MIRMIS instrument is compact (548.5 x 282.0 x 126.8 mm) and low mass (

Abstract:

Ground test data from the Lunar Thermal Mapper instrument. Described in Bowles et al. 2025 submitted to JGR Planets.

Abstract:

A laboratory study was performed using the Visible 91̽�� Space Environment Goniometer in which the broadband (350–1250 nm) bidirectional reflectance distribution functions (BRDFs) of two representative Apollo regolith samples were measured, for two surface roughness profiles, across a range of viewing angles—reflectance: 0–70°, in steps of 5°; incidence: 15°, 30°, 45°, and 60°; and azimuthal: 0°, 45°, 90°, 135°, and 180°. The BRDF datasets were fitted using the Hapke BRDF model to (1) provide a method of comparison to other photometric studies of the lunar regolith and (2) to produce Hapke parameter values which can be used to extrapolate the BRDF to all angles. Importantly, the surface profiles of the samples were characterized using an Alicona 3D® instrument, allowing two of the free parameters within the Hapke model, φ and θ ¯ $$ \overline{\theta} $$ , which represent porosity and surface roughness, respectively, to be constrained. The study determined that, for θ ¯ $$ \overline{\theta} $$ , the 500–1000 μm size‐scale is the most relevant for the BRDF. Thus, it deduced the following “best fit” Hapke parameters for each of the samples: Apollo 11 rough— w $$ w $$ = 0.315 ± 0.021, b $$ b $$ = 0.261 ± 0.007, and h S $$ {h}_S $$ = 0.039 ± 0.005 (with θ ¯ $$ \overline{\theta} $$ = 21.28° and φ = 0.41 ± 0.02); Apollo 11 smooth— w $$ w $$ = 0.281 ± 0.028, b $$ b $$ = 0.238 ± 0.008, and h S $$ {h}_S $$ = 0.032 ± 0.006 (with θ ¯ $$ \overline{\theta} $$ = 13.80° and φ = 0.60 ± 0.02); Apollo 16 rough— w $$ w $$ = 0.485 ± 0.155, b $$ b $$ = 0.155 ± 0.083, and h S $$ {h}_S $$ = 0.135 ± 0.007 (with θ ¯ $$ \overline{\theta} $$ = 21.69° and φ = 0.55 ± 0.02); Apollo 16 smooth— w $$ w $$ = 0.388 ± 0.057, b $$ b $$ = 0.063 ± 0.033, and h S $$ {h}_S $$ = 0.221 ± 0.011 (with θ ¯ $$ \overline{\theta} $$ = 14.27° and φ = 0.40 ± 0.02). Finally, updated hemispheric albedo functions were determined for the samples, which can be used to set laboratory measured visible scattering functions within thermal models.